[ Chinese wardrobe net ] The wardrobe is available in many styles on the market. Choosing the right wardrobe is something we must understand. If the bedroom space is small, many families will make sliding door wardrobes. This not only saves space, but also makes the bedroom environment more beautiful and practical. Then let's take a look at the sliding door wardrobe picture together .
Many people say that the borders and rails are good or bad to see the brand. This is wrong. There is no frame and slide rails of the factory. It is not going to the profile factory. Any factory purchases are in tons, assuming today's aluminum (or alloy) market. The price is 5000, then the profile factory bought the post-sold and sold out 7000. The good rails and the frame and the poor purchase price are the same price in tons, but the good rails and the frame should be thicker and wider. Thin and narrow can be 2000 meters, thick and wide can only have 1000 meters, it is such a difference. So, let's see if the width and thickness of the border are good or bad. The frame and the slide rail are generally pure material (note that this is only a small part of the cost). The general cost of Y is 30--40 square meters, the mid-range 50--70 square, and the good can reach 70--80 square. . Of course, it is still necessary to pinch the hardness, some are not alloys used, and the hardness is not enough.
The pulley can also determine the cost of the sliding door wardrobe, but the impact is very small, a few dollars. Sometimes we see that people in the industry like to promote his things. The hardware is good. It seems that he is expensive because of these, at least I think it is too publicity. Especially the cabinets, the hardware is not produced by you, who can't get in? The cabinet makers advertised Blum hardware to prove how good his cabinet is. If you get it, you can use Blum in the standard configuration. It is much more expensive than domestic ones, but how much can the hinge cost? The cabinets I sell also have Blum's hinges, which is 25 meters more expensive than the ones. What hinges are used to buy, and there is no technical content.
The door of the sliding door wardrobe is generally a wooden sliding door, or it has a certain technical content. Just like our door panel, there are certain requirements for the shape, substrate and surface treatment. This should still be judged. This cost is generally between 30.40---150,160.
Of the world's steel, 60 to 70% are sheets, most of which are stamped into finished products. The car body, chassis, fuel tank, radiator fins, boiler drums, container shells, motors, laminations, etc, are all stamped and processed. There are also a large number of Stamping Parts in products such as instruments, household appliances, bicycles, office machinery, and living utensils.
Compared with castings and forgings, stamping parts have the characteristics of thinness, uniformity, lightness, and strength. Stamping can produce workpieces with reinforcing ribs, ribs, undulations, or flanges that are difficult to manufacture by other methods to improve their rigidity. Due to the use of precision molds, the precision of the workpiece can reach the micron level, and the repeatability is high.
Stamping is an efficient production method. Using compound dies, especially the progressive die, multiple stamping processes can be completed on one press. Generally, hundreds of pieces per minute can be produced by high production efficiency, good working conditions, low production cost.
Here are a few stamping parts manufactured by our company.
1. Sheet Metal Threaded Nut
The part is stamped from the cold-rolled steel sheet. The middle hole is threaded, the surface is electroplated. It acts as a nut during use and is used on occasions where the force is not too heavy. The cost of this part is lower than that of ordinary hexagonal nuts, and the weight is lighter than that of hexagonal nuts too. This part is often used in household products. If you need this type of part, please feel free to contact us. We can customize the parts according to customer requirements.
2. Contact Plate for Battery
This contact plate is used on almost all occasions where there are batteries. This part is a square piece with protrusions, which is the contact position of the battery. The parts have no burrs. All sharp corners were eliminated. The surface is high-gloss and bright. The part is stamped from the brass sheet. The surface is electroplated to prevent oxidation. Our company has rich experience on producing this kind of parts. If you have any needs, please feel free to contact us.
3. Aluminum Sheet Cushion
This part is a round piece with 2 square slots and some holes. It plays the role of a cushion in the machine. The part was stamped from the thin aluminum sheet. The accuracy of dimension can be guaranteed by die and process. The part surface is smooth and free of burrs. The raw material has a protective film to ensure that the surface will not be scratched. Such parts are widely used in industrial, commercial, and household products. Our technology and processing capabilities can fully meet customer requirements. We are confident to provide the parts with high-quality and reasonable price.
4. Stainless Steel Sheet Lid
The part is a round cover with a slender groove on the top surface and raised rim around it. The part is stamped from a high-gloss stainless steel sheet. The surface is very bright and smooth. There is a film on the raw material to protect the surface from scratching. The part is the appearance part of the product. Similar parts can be seen on many household products. Our stamping products are all customized by customers. Please contact us if you have the stamping part demand.
5. Deepdraw Round Cap
The shape of the part is hemispherical with protruding edges. It is drawn out of a cold-rolled steel sheet. In addition to blanking parts, our company also has rich processing experience in drawing parts. Over the years, we have provided customers with high-quality, low-price products with excellent services. The stamping parts produced by our company are all customized by customers. If you need stamping parts, please feel free to contact us.
Sheet Metal Threaded Nut, Contact Plate for Battery, Aluminum Sheet Cushion, Stainless Steel Sheet Lid, Deepdraw Round Cap
YRX Technology (Shenzhen) Co., Ltd. , https://www.yrx-tech.com